CoolPi 4B无法进入Android系统
-
CoolPi 4B 从SD卡启动,在系统启动阶段会出现随机卡死/无限重启的情况,操作步骤如下:
下载20230517-coolpi-4b-android12镜像,使用balena etcher烧录到SD卡中,启动系统,从串口看输出,不能进入系统,具体表现是在加载系统时无限重启(之前遇到过,今天没有遇到)或卡死(如图)
尝试过的解决方案:
1.更换2023042819-coolpi-4b-android镜像,同样卡死
2.更换SD卡,仍然卡死
3.把SD卡插上读卡器,从靠下的USB3.0进行引导,仍然卡死
4.更换功率更大的充电器(之前用的是官方自带的)
请问一下有大佬遇见过这种情况吗?不胜感激! -
重启时的截图如下:
-
@traceback
从log信息看固件的分区有问题导致,先把SD卡格式化一下,然后重新制作启动盘。 -
@george 你好,问题还是这样,有的时候卡死,有的时候无限重启,我买了新的读卡器和闪迪的SD卡,并且对SD卡进行了格式化,log如下:
Device 0: unknown device switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 434 bytes read in 7 ms (60.5 KiB/s) 1: Android coolpi Retrieving file: /initrd.img reading /initrd.img 13538757 bytes read in 1089 ms (11.9 MiB/s) Retrieving file: /Image reading /Image 38920200 bytes read in 3122 ms (11.9 MiB/s) append: androidboot.mode=normal androidboot.serialno=9572efc46eee3f67 console=ttyS0,115200 firmware_class.path=/vendor/etc/firmware init=/init rootwait ro loop.max_part=7 androidboot.wificountrycode=CN androidboot.hardware=rk30board androidboot.boot_devices=fe2e0000.mmc androidboot.selinux=permissive irqchip.gicv3_pseudo_nmi=0 rtleth=ethaddr:22:6e:92:0d:db:66 Retrieving file: /rk3588s-cp4.dtb reading /rk3588s-cp4.dtb 225093 bytes read in 24 ms (8.9 MiB/s) ## Flattened Device Tree blob at 0x0a100000 Booting using the fdt blob at 0x0a100000 'reserved-memory' ramoops@110000: addr=110000 size=e0000 Loading Ramdisk to eacea000, end eb9d35c5 ... OK Loading Device Tree to 00000000eacb0000, end 00000000eace9f44 ... OK Card did not respond to voltage select! mmc_init: -95, time 17 Card did not respond to voltage select! mmc_init: -95, time 16 ** Bad device mmc 0 ** switch to partitions #0, OK mmc1 is current device ** Unable to read file logo_kernel.bmp ** Card did not respond to voltage select! mmc_init: -95, time 17 Card did not respond to voltage select! mmc_init: -95, time 17 ** Bad device mmc 0 ** switch to partitions #0, OK mmc1 is current device ** Unable to read file logo_kernel.bmp ** Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000) Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000) Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000) Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000) ...... [ 18.914489][ T7] combophy_avdd0v85: supplied by vdd_0v85_s0 [ 18.914743][ T165] mali fb000000.gpu: Kernel DDK version g13p0-01eac0 [ 18.921218][ T7] combophy_avdd1v8: supplied by avcc_1v8_s0 [ 18.927539][ T165] mali fb000000.gpu: leakage=14 [ 18.935651][ T7] vcc_mipidphy0: supplied by vcc_3v3_s3 [ 18.937364][ T165] debugfs: Directory 'fb000000.gpu-mali' with parent 'vdd_gpu_s0' already present! [ 18.950906][ T7] vcc3v3_lcd0_n: supplied by vcc_3v3_s0 [ 18.953473][ T165] mali fb000000.gpu: pvtm=859 [ 18.960490][ T7] vcc_3v3_sd_s0: supplied by vcc_3v3_s3 [ 18.964960][ T165] mali fb000000.gpu: pvtm-volt-sel=2 [ 18.973526][ T165] mali fb000000.gpu: avs=0 [ 18.973729][ T7] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2 [ 18.980417][ T165] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 136; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available. [ 18.988343][ T7] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3 [ 19.005393][ T165] mali fb000000.gpu: GPU hardware issue table may need updating: [ 19.005393][ T165] r0p0 status 5 is unknown; treating as r0p0 status 0 [ 19.014368][ T7] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8 [ 19.028533][ T165] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0 [ 19.039113][ T7] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9 [ 19.047048][ T165] mali fb000000.gpu: No priority control manager is configured [ 19.057596][ T7] rockchip-drm display-subsystem: failed to get hdmi0_phy_pll: -2 [ 19.064985][ T165] mali fb000000.gpu: No memory group manager is configured [ 19.072619][ T7] rockchip-drm display-subsystem: failed to get hdmi1_phy_pll: -2 [ 19.079672][ T165] mali fb000000.gpu: Protected memory allocator not available [ 19.095418][ T165] mali fb000000.gpu: Capping CSF_FIRMWARE_TIMEOUT to CSF_FIRMWARE_PING_TIMEOUT [ 19.099506][ T7] rockchip-drm display-subsystem: bound fdd90000.vop (ops vop2_component_ops) [ 19.104838][ T165] mali fb000000.gpu: Couldn't find power_model DT node matching 'arm,mali-simple-power-model' [ 19.114748][ T7] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver [ 19.122965][ T165] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.static-coefficient = 1*[0] [ 19.130580][ T7] rockchip-drm display-subsystem: bound fde80000.hdmi (ops dw_hdmi_rockchip_ops) [ 19.140734][ T165] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.dynamic-coefficient = 1*[0] [ 19.149573][ T7] rockchip-drm display-subsystem: bound fde20000.dsi (ops dw_mipi_dsi2_ops) [ 19.160003][ T165] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.ts = 4*[0] [ 19.168438][ T7] rockchip-drm display-subsystem: bound fde50000.dp (ops dw_dp_component_ops) [ 19.177344][ T165] mali fb000000.gpu: Error -22, no DT entry: mali-simple-power-model.thermal-zone = '' [ 19.186998][ T7] rockchip-drm display-subsystem: route-dsi0: failed to get logo,offset [ 19.196941][ T165] mali fb000000.gpu: Using configured power model mali-lodx-power-model, and fallback mali-simple-power-model [ 19.203631][ T7] rockchip-drm display-subsystem: connector[HDMI-A-1] can't found any modes [ 19.215090][ T165] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0 [ 19.223542][ T7] rockchip-drm display-subsystem: can't not find any logo display [ 19.240476][ T7] rockchip-drm display-subsystem: failed to show kernel logo [ 19.248932][ T7] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device [ 19.253405][ T165] mali fb000000.gpu: Probed as mali0 [ 19.263466][ T7] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0 [ 19.272254][ T7] input: adc-keys as /devices/platform/adc-keys/input/input1 [ 19.280578][ T7] debugfs: File 'Capture' in directory 'dapm' already present! [ 19.347784][ T165] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode. [ 19.348504][ T1] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1 [ 19.355569][ T165] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller. [ 19.362170][ T1] rockchip-csi2-dphy0: No link between dphy and sensor [ 19.369473][ T165] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a [ 19.376298][ T1] rockchip-csi2-dphy0: No link between dphy and sensor [ 19.382434][ T165] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 80,32 bit host data width,256 deep fifo [ 19.389098][ T1] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 19.389102][ T1] rkcif-mipi-lvds2: Async subdev notifier completed [ 19.412646][ T165] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 19.415579][ T1] rockchip-csi2-dphy0: No link between dphy and sensor [ 19.415585][ T1] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 19.441973][ T1] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP [ 19.450545][ T181] rockchip-csi2-dphy0: No link between dphy and sensor [ 19.450978][ T1] RKNPU fdab0000.npu: Adding to iommu group 0 [ 19.457269][ T181] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed! [ 19.463222][ T1] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode [ 19.472984][ T181] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP [ 19.492334][ T1] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff] [ 19.501553][ T1] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff] [ 19.510759][ T1] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff] [ 19.520096][ T1] [drm] Initialized rknpu 0.8.2 20220829 for fdab0000.npu on minor 1 [ 19.522504][ T172] mmc_host mmc2: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0) [ 19.531219][ T1] RKNPU fdab0000.npu: leakage=7 [ 19.543419][ T1] debugfs: Directory 'fdab0000.npu-rknpu' with parent 'vdd_npu_s0' already present! [ 19.559146][ T1] RKNPU fdab0000.npu: pvtm=871 [ 19.560277][ T172] dwmmc_rockchip fe2c0000.mmc: Successfully tuned phase to 135 [ 19.570375][ T1] RKNPU fdab0000.npu: pvtm-volt-sel=3 [ 19.571173][ T172] mmc2: new ultra high speed SDR104 SDXC card at address aaaa [ 19.576605][ T1] RKNPU fdab0000.npu: avs=0 [ 19.584318][ T172] mmcblk2: mmc2:aaaa SR64G 59.5 GiB [ 19.588080][ T1] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0 [ 19.599272][ T172] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 19.631946][ T1] RKNPU fdab0000.npu: failed to find power_model node [ 19.638561][ T1] RKNPU fdab0000.npu: RKNPU: failed to initialize power model [ 19.645865][ T1] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient [ 19.653876][ T1] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 19.663497][ T1] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 19.670755][ T138] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 19.680057][ T138] cfg80211: failed to load regulatory.db [ 19.686056][ T1] rockchip-pm rockchip-suspend: not set pwm-regulator-config [ 19.693591][ T1] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 409; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '18:43:18', on 'May 17 2023'. [ 19.714508][ T1] Mali: [ 19.714509][ T1] Mali device driver loaded [ 19.721558][ T1] rkisp rkisp0-vir0: clear unready subdev num: 1 [ 19.727842][ T1] rkisp0-vir0: Async subdev notifier completed [ 19.733838][ T1] ALSA device list: [ 19.737493][ T1] #0: rockchip,hdmi0 [ 19.741405][ T1] #1: rockchip,es8316-codec [ 19.745970][ T1] dw-apb-uart feb50000.serial: forbid DMA for kernel console [ 19.753392][ T1] Freeing unused kernel memory: 1344K [ 19.764203][ T1] Run /init as init process wait for device. 0x5344 [ 19.919481][ T250] Set signal voltage to initial state [ 19.925076][ T250] rk860-regulator 2-0042: rk860..... reset [ 19.931741][ T250] rk860-regulator 2-0042: force rk860x_reset ok! [ 19.937936][ T250] rk860-regulator 0-0043: rk860..... reset [ 19.944591][ T250] rk860-regulator 0-0043: force rk860x_reset ok! [ 19.950786][ T250] rk860-regulator 0-0042: rk860..... reset [ 19.957441][ T250] rk860-regulator 0-0042: force rk860x_reset ok! [ 19.968899][ T250] mpp_av1dec av1d-master: shutdown device [ 19.974480][ T250] mpp_av1dec av1d-master: shutdown success [ 19.980282][ T250] [WLAN_RFKILL]: Enter rfkill_wlan_shutdown [ 19.986026][ T250] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 19.991424][ T250] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false [ 19.998013][ T250] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1] [ 20.004108][ T250] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 0 [ 20.010059][ T250] rkisp_hw fdcb0000.rkisp: rkisp_hw_shutdown [ 20.015895][ T250] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown device [ 20.022323][ T250] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown success [ 20.028845][ T250] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown device [ 20.035273][ T250] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown success [ 20.041795][ T250] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown device [ 20.048222][ T250] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown success [ 20.054747][ T250] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown device [ 20.061176][ T250] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown success [ 20.067699][ T250] mpp-iep2 fdbb0000.iep: shutdown device [ 20.073173][ T250] mpp-iep2 fdbb0000.iep: shutdown success [ 20.078740][ T250] mpp_vepu2 fdbac000.jpege-core: shutdown device [ 20.084908][ T250] mpp_vepu2 fdbac000.jpege-core: shutdown success [ 20.091169][ T250] mpp_vepu2 fdba8000.jpege-core: shutdown device [ 20.097335][ T250] mpp_vepu2 fdba8000.jpege-core: shutdown success [ 20.103596][ T250] mpp_vepu2 fdba4000.jpege-core: shutdown device [ 20.109764][ T250] mpp_vepu2 fdba4000.jpege-core: shutdown success [ 20.116024][ T250] mpp_vepu2 fdba0000.jpege-core: shutdown device [ 20.122193][ T250] mpp_vepu2 fdba0000.jpege-core: shutdown success [ 20.128455][ T250] mpp_jpgdec fdb90000.jpegd: shutdown device [ 20.134276][ T250] mpp_jpgdec fdb90000.jpegd: shutdown success [ 20.140202][ T250] mpp_vepu2 fdb50000.vepu: shutdown device [ 20.145850][ T250] mpp_vepu2 fdb50000.vepu: shutdown success [ 20.151584][ T250] mpp_vdpu2 fdb50400.vdpu: shutdown device [ 20.157232][ T250] mpp_vdpu2 fdb50400.vdpu: shutdown success [ 20.163049][ T250] xhci-hcd xhci-hcd.4.auto: remove, state 4 [ 20.168786][ T250] usb usb6: USB disconnect, device number 1 [ 20.174793][ T250] xhci-hcd xhci-hcd.4.auto: USB bus 6 deregistered [ 20.181314][ T250] xhci-hcd xhci-hcd.4.auto: remove, state 4 [ 20.187057][ T250] usb usb5: USB disconnect, device number 1 [ 20.193103][ T250] xhci-hcd xhci-hcd.4.auto: USB bus 5 deregistered [ 20.200265][ T250] reboot: Restarting system
-
@traceback 使用2023042819-coolpi-4b-android镜像,会卡死在I/TC: Secondary CPU 7 switching to normal world boot