• Register
    • Login
    • Search
    • Recent
    • Wiki
    • Github
    • 百度网盘
    • Onedrive
    • Official
    • Shop

    CM5刷uboot找不到设备

    Pi CM5
    3
    17
    547
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • J
      jugg last edited by

      dd7b7e87-a297-4385-bf22-c28f37c9f483-image.png

      G 1 Reply Last reply Reply Quote 0
      • G
        george @jugg last edited by

        @jugg
        确认USB接口为上层的USB3.0接口？

        J 3 Replies Last reply Reply Quote 0
        • J
          jugg @george last edited by

          @george
          是USB3的上层 需要短接还是其他什么操作 我看wifi里面没有相关说明 cm4的需要短接

          1 Reply Last reply Reply Quote 0
          • J
            jugg @george last edited by

            @george 驱动也安装了

            1 Reply Last reply Reply Quote 0
            • J
              jugg @george last edited by

              @george 现在板子开机停留在coolpi的logo界面

              J 1 Reply Last reply Reply Quote 0
              • J
                jack_admin @jugg last edited by

                @jugg cm5有三个按键，中间一个持续按住，再上电，进入maskrom模式

                J 3 Replies Last reply Reply Quote 0
                • J
                  jugg @jack_admin last edited by

                  @jack_admin
                  cdd44340-3260-483f-a96e-be2ed0097f9d-image.png
                  loader刷好了
                  然后刷系统 按3下PWR 无法进入刷机

                  1 Reply Last reply Reply Quote 0
                  • J
                    jugg @jack_admin last edited by

                    @jack_admin 连续按了很多次PWR 还是不能进入UMS

                    1 Reply Last reply Reply Quote 0
                    • J
                      jugg @jack_admin last edited by

                      @jack_admin
                      这种情况 还可以怎么做 才能刷系统

                      J 1 Reply Last reply Reply Quote 0
                      • J
                        jack_admin @jugg last edited by

                        @jugg 你刷哪个loader，从哪来的，看下串口启动信息

                        J 3 Replies Last reply Reply Quote 0
                        • J
                          jugg @jack_admin last edited by

                          @jack_admin
                          loader 网盘上下的
                          0c589d62-b781-4be9-acbf-0918ae44ef8e-image.png

                          1 Reply Last reply Reply Quote 0
                          • J
                            jugg @jack_admin last edited by

                            @jack_admin
                            一直在重启

                            DDR V1.10 75d050770f typ 23/02/28-20:47:10
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:26.7%, TX Vref:22.8%,20.8%
CH1 RX Vref:26.7%, TX Vref:22.8%,21.8%
CH2 RX Vref:27.9%, TX Vref:22.8%,23.8%
CH3 RX Vref:28.5%, TX Vref:23.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-557-g9609b9c19:derrick.huang
NOTICE:  BL31: Built : 14:29:57, Mar  8 2023
INFO:    spec: 0x1
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022年 09月 20日 星期二 09:41:09 CST aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


COOLPI LOADER BY YANYI(Apr 11 2023)

DRAM:  8 GiB
Using default environment

0 2 1 3 6 8 7 9 Monitor has basic audio support
hdmi info isn't saved in main block
mode:3840x2160 bus_format:0x2026
hdmi@fde80000:  detailed mode clock 594000 kHz, flags[5]
    H: 3840 4016 4104 4400
    V: 2160 2168 2178 2250
bus_format: 2026
VOP update mode to: 3840x2160p0, type: HDMI0 for VP0
dclk:297000,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: hdmi0_phy_pll may not define
rockchip_vop2_init: hdmi1_phy_pll may not define
assigned-clock-parents's node not define
VP0 set crtc_clock to 594000KHz
VOP VP0 enable Esmart0[356x124->356x124@1742x1018] fmt[1] addr[0xedf21000]
CEA mode used vic=97
mtmdsclock:297000000
bus_width:0x2d5190,bit_rate:2970000
hdptx_ropll_cmn_config bus_width:2d5190 rate:2970000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
boot mode: None
Net Initialization Skipped
Autoboot in 1 seconds
VOP VP0 enable Esmart0[356x124->356x124@1742x1018] fmt[1] addr[0xedf21000]
MMC: no card present
mmc_init: -123, time 1
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fc400000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1
WARN: interface 1 has 14 endpoint descriptor, different from the interface descriptor's value: 2
3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fc400000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
scanning bus for devices...
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp fbss pio slum part ccc apst 

Device 0: unknown device
switch to partitions #0, OK
mmc0(part 0) is current device
** Invalid partition 1 **
Loading order: tf - usb - sata - emmc
MMC: no card present
mmc_init: -123, time 2
MMC: no card present
mmc_init: -123, time 2
** Bad device mmc 1 **
MMC: no card present
mmc_init: -123, time 2
** Bad device mmc 1 **
resetting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fc400000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1
WARN: interface 1 has 14 endpoint descriptor, different from the interface descriptor's value: 2
3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fc400000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
scanning bus for devices...
checkconf - 

Usage:
checkconf 

** Bad device scsi 0 **
switch to partitions #0, OK
mmc0(part 0) is current device
** Invalid partition 1 **
** Invalid partition 1 **
DDR V1.10 75d050770f typ 23/02/28-20:47:10
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:26.7%, TX Vref:22.8%,20.8%
CH1 RX Vref:26.7%, TX Vref:22.8%,21.8%
CH2 RX Vref:27.5%, TX Vref:22.8%,23.8%
CH3 RX Vref:28.5%, TX Vref:23.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-557-g9609b9c19:derrick.huang
NOTICE:  BL31: Built : 14:29:57, Mar  8 2023
INFO:    spec: 0x1
INFO:    ext 32k is valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022年 09月 20日 星期二 09:41:09 CST aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


COOLPI LOADER BY YANYI(Apr 11 2023)

DRAM:  8 GiB
Using default environment

0 2 1 3 6 8 7 9 Monitor has basic audio support
hdmi info isn't saved in main block
mode:3840x2160 bus_format:0x2026
hdmi@fde80000:  detailed mode clock 594000 kHz, flags[5]
    H: 3840 4016 4104 4400
    V: 2160 2168 2178 2250
bus_format: 2026
VOP update mode to: 3840x2160p0, type: HDMI0 for VP0
dclk:297000,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: hdmi0_phy_pll may not define
rockchip_vop2_init: hdmi1_phy_pll may not define
assigned-clock-parents's node not define
VP0 set crtc_clock to 594000KHz
VOP VP0 enable Esmart0[356x124->356x124@1742x1018] fmt[1] addr[0xedf21000]
CEA mode used vic=97
mtmdsclock:297000000
bus_width:0x2d5190,bit_rate:2970000
hdptx_ropll_cmn_config bus_width:2d5190 rate:2970000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
boot mode: None
Net Initialization Skipped
Autoboot in 1 seconds
VOP VP0 enable Esmart0[356x124->356x124@1742x1018] fmt[1] addr[0xedf21000]
MMC: no card present
mmc_init: -123, time 2
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fc400000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1
WARN: interface 1 has 14 endpoint descriptor, different from the interface descriptor's value: 2
3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fc400000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
scanning bus for devices...
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp fbss pio slum part ccc apst 

Device 0: unknown device
switch to partitions #0, OK
mmc0(part 0) is current device
** Invalid partition 1 **
Loading order: tf - usb - sata - emmc
MMC: no card present
mmc_init: -123, time 2
MMC: no card present
mmc_init: -123, time 2
** Bad device mmc 1 **
MMC: no card present
mmc_init: -123, time 2
** Bad device mmc 1 **
resetting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fc400000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1
WARN: interface 1 has 14 endpoint descriptor, different from the interface descriptor's value: 2
3 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fc400000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
                            1 Reply Last reply Reply Quote 0
                            • J
                              jugg @jack_admin last edited by

                              @jack_admin
                              我这上面装了一块SSD硬盘 这个有影响？
                              系统之前是能进去的 就是用Etcher刷系统的时候 中途取消了 然后就进不去系统也不能重新刷
                              所以就刷了loader 看看能不能重新刷系统

                              J 1 Reply Last reply Reply Quote 0
                              • J
                                jack_admin @jugg last edited by

                                @jugg 重新格式化一次emmc，还是进maskrom，用高级工具里导入loader再擦除emmc

                                J 1 Reply Last reply Reply Quote 0
                                • J
                                  jugg @jack_admin last edited by

                                  @jack_admin
                                  fd107625-32a5-40cb-a477-680ae4ca77ba-image.png
                                  这样擦除EMMC吗？
                                  高级工具里没有导入loader?
                                  步骤能清晰一点吗

                                  J 1 Reply Last reply Reply Quote 0
                                  • J
                                    jack_admin @jugg last edited by

                                    @jugg 主板先进入maskrom模式，点击图片中下载左侧图标，加载loader文件，再点击下载。接着进行切换emmc存储，再擦除

                                    J 1 Reply Last reply Reply Quote 0
                                    • J
                                      jugg @jack_admin last edited by

                                      @jack_admin
                                      刷机成功

                                      1 Reply Last reply Reply Quote 0
                                      • 1 / 1
                                      • First post
                                        Last post