@enok71
George ppa provides ffmpeg source code and its patches, and can continue to develop on this code. We hope to support more formats. Especially in the coding part.

@george I updated the OS by connecting to the top of the USB3.0 blue connector.

@jugg
如果是TI的库仑计，而且内核有驱动，正常DTS配置一下就可以了。如果是linux内核没有的库仑计型号，就需要自己加驱动，相对麻烦一点。

@george

0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01) 0000:01:00.0 Non-Volatile memory controller: Micron Technology Inc Device 6001 (rev 03) 0003:30:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01) 0003:31:00.0 Network controller: Broadcom Inc. and subsidiaries Device 449d (rev 02) Bus 006 Device 002: ID 0781:5581 SanDisk Corp. Ultra Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 058e:3864 Tripath Technology, Inc. USB Camera Bus 002 Device 002: ID 1a86:8091 QinHeng Electronics USB HUB Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 002: ID 1c4f:006b SiGma Micro USB Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

@george
好的

@Eel
There is currently no separate purchase link for the casing of this machine. If any part of your machine is damaged, you can send it out and I can coordinate with the factory to see if it can be shipped separately.

@George 好的晚上试下。
extlinux.conf 文件中， append 那一行 追加 “cmdline”

@jugg
暂时没有做其他版本的适配。

@george Thanks a lot, I will contact the Aliexpress seller

@Momo-0 any help is appreciated

@anernest
Ensure that the LCD is an EDP interface and the touch is an IIC interface. In principle, it can light up normally, but the driver part needs to be modified. Check if there are any universal specifications later.

@ccjjww1222 感谢您的支持。百度的fastdeploy仓库我已经初步适配完毕了，目前计划11.11在bilibili将有个直播，有Picodet（Detection）和PPHumanSeg的部署过程，有时间可以来看看。

机器没有识别到这个HDMI设备。可能是接口或者分辨率非标准导致。

@george Excellent!

@retroman Because the pi 4b box has no power key location, direct use will cause pwr key is stuck. In addition, the size of the DP output port is larger than Pi 4b, and the size of the metal radiator of PI4b is too far from the DP interface. 3D printing is the only option before the surrounding accessories of the cool pi come out.

@大法师 @george

太神啦！感謝

@tonyone0902 显示异常的时候，打印一下下面两个命令，结果发上来：
sudo cat /sys/kernel/debug/dri/0/summary
sudo cat /sys/kernel/debug/dw-hdmi0/status

@大法师 Hi again, can you please check in a basic README to that fedora repo? I am not able to fork it because there are no commits.

@test 你的loader版本看起来比较早，升级loader试下。卡的分区表异常，格式化一次